You are here:

Frontline - 105mm Front & Double Glaze

INTRODUCTION
The Sapphire Frontline Suite is primarily used for framing plasterboard walls and glass where a sleek front glazed look is required similar to curtain walls. The glass can also be mounted to the back or combinations of front and back or double glazed where high sound ratings are required for meeting rooms or senior management (partner) offices.

COMMON USE
Commercial Office Partitions such as law firms or banks , Meeting Rooms

FRAME OPTIONS

  • Single & Double Glaze 105mm x 50mm

GLAZING OPTIONS
Single glazed 6mm - 14.50mm as per AS1288-2006

DOOR OPTIONS
HINGED - Timber or Glass Doors 32mm - 50mm in thickness
SLIDING - Timber or Sapphire Shooshline Alum Doors 45mm in thickness

PLASTERBOARD OPTIONS
Various as this is a glass framing system it can be used in conjunction with standard set plasterboard walls or any of the other available Sapphire Partition Suites.

For more information on this product contact your local Sapphire agent or fill out the email contact form.

back to top >>

Acoustic Performance

Slimline Aluminium Partitions Acoustics

Walls
The Frontline Suite will accommodate walls constructed with the following:

  • 64mm Steel Studs and two sheets of 13mm plaster board
  • 51mm Steel Studs and three sheets of 13mm plaster board

Wall accoustics

Glass
The Frontline Suite will accommodate single and double glazing from 6mm - 14.5mm.

Glass Accoustics of Wall Partition

Please note: The acoustic performance estimate of Sapphire Partition Systems is expressed in terms of Rw and Rw+Ctr. The performance of the as built system may be affected by - soundflaking and or the effectiveness of workmanship and other elements outside of Sapphire's control.

back to top >>

Specification/Care & Maintenance

SPECIFICATION
The Sapphire Frontline Suite of sections have been developed with over 25 years of experience in supply of suites to the partition industry and is designed to meet the relevant glazing codes and construction codes for internal framing, however fabricators of aluminium frames should seek certification by a consultant engineer as to the framing being acceptable for the local design impact safety and deflection characteristics required of the site. Detailed calculations should be provided with final drawings of the aluminium frames.

ALLOY
The Sapphire Frontline Suite is extruded from primary billet only (No remelt) 6060T5 alloy ensuring that it is of the highest quality suitable for anodising finishes and maintaining colour uniformity from batch to batch.

ALUMINIUM
Partition suite to be Frontline by Sapphire Aluminium Pty Ltd (not "equal or equivalent"-see note below*)provided with the specified finish detailed in the finishes schedule and installed in accordance with the project design detail and relevant building codes."

LARGE FRAME - 50MM
The maximum recommended panel height shall be 3500mm.

HARDWARE
Glazing wedges shall be Sapphire's colour coded wedges for Frontline Partition Suite to suit standard glazing options. Hinges shall be as per Sapphire Technical Manual. All other hardware as per Sapphire Technical Manual.

FINISHES
All anodised material shall be produced by Sapphire to AS1231
All powder coated material shall be produced by Sapphire to AS3715

CARE AND MAINTENANCE
Sapphire Frontline Partition Suite should only ever need to be washed down with warm water and a mild detergent by rubbing with a soft cloth Ensure that the cloth is rinsed well with fresh water to remove any detergent residue.
For more information refer to our website www.sapal.com.au

WARNING!
Strong detergents and abrasive cleaners should never be used to clean the Sapphire Frontline Partition Suite as it may cause scratching or damage to the coated surface. All products are available from Sapphire Aluminium Pty Ltd (A.B.N. 84 123 804 571 ) as detailed in the "SAPPHIRE" Catalogue or on the Internet at www.sapal.com.au .

PLEASE NOTE !

  • excluding the words " equal or equivalent" will avoid substitution of products that in many cases are anything but "equal or equivalent". To further ensure you are provided with quality locally produced Sapphire partition systems you may wish to specify a quality Sapphire coloured anodised finish from our extensive range. These finishes can seldom be achieved on inferior imported extrusions thus preventing substitution of inferior products.
  • customised profiles are subject to minimum order quantites
  • customised profiles are subject to minimum order quantites

Profiles are subject to change or deletion without notice Please check on availability prior to specifying or ordering.

back to top >>