You are here:

Maxline 76mm - 116mm x 44mm Centre, Front & Double Glaze

Maxline 76mm , when you require a larger frame with options of Centre, front and double glaze

INTRODUCTION

 

76mm Maxline is designed for institutions where performance and longevity are required for a rigourous service life. Maxline is designed to be stronger to meet these needs as well as accommodating 76mm Steel Studs.The system will accommodate steel mesh or fibre cement board behind the plasterboard where security and strength is a requirement.

COMMON USE

Commercial Office Partitions, Schools, Universites and Government

FRAME OPTIONS
STANDARD detail - 116mm x 45mm

GLAZING OPTIONS

  • Single glazed 6mm - 12.38mm as per AS1288-2006
  • Front glazed 6mm - 14.50mm as per AS1288-2006
  • Double glazed 6mm - 14.50mm as per AS1288-2006

DOOR OPTIONS
HINGED - Timber or Glass Doors 32mm - 45mm in thickness
SLIDING - Timber or Sapphire Shooshline Alum Doors 45mm in thickness

DOOR STOPS
35mm, 40mm & 45mm Options to edge of frame
12mm High accepts acoustic seals and smoke seals

PLASTERBOARD OPTIONS

  • 76mm Steel Studs and two sheets of 13mm plasterboard
  • 64mm Steel Studs and three sheets of 13mm plasterboard.
  • 64mm Steel Studs and two sheets of 13mm, one sheet of 10mm plasterboard with 1 sheet of 3mm Stanless or Steel Sheet.
  • 51mm Steel Studs and four sheets of 13mm plasterboard.
  • Shadowline details optional Drywall construction optional (Semi-Demountable)

For more information on this product contact your local Sapphire agent or fill out the contact form.

back to top >>

Acoustic Performance

Acoustic Performance
WallsThe 76mm Maxline suite will accommodate walls constructed with the following

  • 76mm Steel Studs and two sheets of 13mm plasterboard
  • 64mm Steel Studs and Three sheets of 13mm plasterboard
  • .51mm Steel Studs and four sheets of 13mm plasterboard.

Wall accoustics

Glass

  • 76mm Maxline Gen 2 Suite will accommodate  glazing from 6mm - 14.50mm.

.

Please note: The acoustic performance estimate of Sapphire Partition Systems is expressed in terms of Rw and Rw+Ctr. The performance of the as built system may be affected by - soundflaking and or the effectiveness of workmanship and other elements outside of Sapphire's control.

back to top >>

Specification/Care & Maintenance

SPECIFICATION

The Sapphire 76mm Maxline Suite of sections have been developed with over 25 years of experience in supply of suites to the partition industry and is designed to meet the relevant glazing codes and construction codes for internal framing, however fabricators of aluminium frames should seek certification by a consultant  engineer as to the framing being acceptable for the local design impact safety and deflection characteristics required of the site.  Detailed calculations should be provided with final drawings of the aluminium frames.
ALLOY
The Sapphire 76mm Maxline Suite is extruded from primary billet only (No remelt) 6060T5 alloy ensuring that it is of the highest quality suitable for anodising finishes and maintaining colour uniformity from batch to batch.
ALUMINIUM
Partition suite to be 76mm Maxline by Sapphire Aluminium Pty Ltd (not “equal or equivalent”-see note below*)provided with the specified finish detailed in the finishes schedule and installed in accordance with the project design detail and relevant building codes.”
STANDARD Frame - 44mm
The maximum panel height shall be 3500mm.
HARDWARE
Glazing wedges shall be Sapphire’s colour coded wedges for 76mm Maxline® Partition Suite
to suit standard glazing options.
Hinges shall be as per Sapphire Technical Manual.
All other hardware as per Sapphire Technical Manual.
FINISHES
All anodised material shall be produced by Sapphire to AS1231
All powder coated material shall be produced by Sapphire to AS3715
Care And Maintenance
Sapphire 76mm Maxline Partition Suite should only ever need to be washed down with warm water and a mild detergent by rubbing with a soft cloth
Ensure that the cloth is rinsed well with fresh water to remove any detergent residue.
For more information refer to our website www.sapal.com.au
WARNING!
Strong detergents and abrasive cleaners should never be used to clean the Sapphire 76mm Maxline Partition Suite as it may cause scratching  or damage to the coated surface.
All products are available from Sapphire Aluminium Pty Ltd (A.B.N. 84 123 804 571 ) as detailed in the “SAPPHIRE” Catalogue or on the Internet at www.sapal.com.au.
PLEASE NOTE !
*excluding the words “ equal or equivalent” will avoid substitution of products that in many cases are anything but “equal or equivalent”.  To further ensure you are provided with quality locally produced Sapphire partition systems you may wish to specify a quality Sapphire coloured anodised finish from our extensive range. These finishes can seldom be achieved on inferior imported extrusions thus preventing substitution of inferior products.
* customised profiles are subject to minimum order quantites
Profiles are subject to change or deletion  without notic.e Please check on availability  prior to specifiying or ordering.