You are here:

Wideline - 105mm Centreglaze

Sapphire's Wideline Suite provides a solid foundation for any fitout with multiple options

INTRODUCTION
Sapphires Wideline Suite provides for a centre glazed framing system for glass up to 14.5mm with a large variety of looks and functions from the wide range of sections available in this suite.

Sections can be mixed and mactched with Frontline and Sliding doors can now be integrated within the frame when combined with our whisper quiet Shooshline Doors.


COMMON USE

Commercial Office Partitions

FRAME OPTIONS
Standard detail - 105mm x 25mm
Medium detail - 105mm x 36mm
Large detail - 105mm x 50mm

GLAZING OPTIONS
Single glazed 6mm - 14.5mm as per AS1288-2006

DOOR OPTIONS
HINGED - Timber or Glass Doors 32mm - 45mm in thickness
SLIDING - Timber or Sapphire Shooshline Alum Doors 45mm in thickness

DOOR STOPS
35mm, 40mm & 45mm Options to edge of frame
12mm High accepts acoustic seals and smoke seals

PLASTERBOARD OPTIONS

64mm Steel Studs and 2 Sheets of 13mm Plasterboard
51mm Steel Studs and 3 Sheets of 13mm Plasterboard
51mm Steel Studs and 2 Sheets of 13mm & 1 Sheet of 10mm Plasterboard with a 3mm Stainless or Steel Sheet.
Shadowline details optional
Drywall construction optional (Semi- Demountable)

For more information on this product contact your local Sapphire agent or fill out the contact form.

back to top >>

Acoustic Performance

Slimline Aluminium Partitions Acoustics

Walls
The Wideline Suite will accommodate walls constructed with the following:

  • 64mm Steel Studs and two sheets of 13mm plaster board
  • 51mm Steel Studs and three sheets of 13mm plaster board

Wall accoustics

Glass
The wideline suite will accommodate single glazing from 6mm - 14.50mm

Glass Accoustics of Wall Partition

Please note: The acoustic performance estimate of Sapphire Partition Systems is expressed in terms of Rw and Rw+Ctr. The performance of the as built system may be affected by - soundflaking and or the effectiveness of workmanship and other elements outside of Sapphire's control.

back to top >>

Specification/Care & Maintenance

SPECIFICATION
The Sapphire Wideline® Suite of sections have been developed with over 25 years of experience in supply of suites to the partition industry and is designed to meet the relevant glazing codes and construction codes for internal framing, however fabricators of aluminium frames should seek certification by a consultant engineer as to the framing being acceptable for the local design impact safety and deflection characteristics required of the site. Detailed calculations should be provided with final drawings of the aluminium frames.

ALLOY
The Sapphire Wideline® Suite is extruded from primary billet only (No remelt) 6060T5 alloy ensuring that it is of the highest quality suitable for anodising finishes and maintaining colour uniformity from batch to batch.

ALUMINIUM
Partition suite to be Wideline® by Sapphire Aluminium Pty Ltd (not "equal or equivalent"-see note below*)provided with the specified finish detailed in the finishes schedule and installed in accordance with the project design detail and relevant building codes."

STANDARD FRAME - 25MM

The maximum recommended panel height shall be 3000mm

MEDIUM FRAME - 36MM

The maximum recommended panel height shall be 3250mm

LARGE FRAME - 50MM

The maximum recommended panel height shall be 3500mm

Please note ! larger panel sizes can be obtained by using transoms

FINISHES
All anodised material shall be produced by Sapphire to AS1231
All powder coated material shall be produced by Sapphire to AS3715

CARE AND MAINTENANCE
Sapphire Wideline® Partition Suite should only ever need to be washed down with warm water and a mild detergent by rubbing with a soft cloth Ensure that the cloth is rinsed well with fresh water to remove any detergent residue.

WARNING!
Strong detergents and abrasive cleaners should never be used to clean the Sapphire Wideline® Partition Suite as it may cause scratching or damage to the coated surface. All products are available from Sapphire Aluminium Pty Ltd (A.B.N. 84 123 804 571 ) as detailed in the "SAPPHIRE" Catalogue.

PLEASE NOTE !
*excluding the words "equal or equivalent" will avoid substitution of products that in many cases are anything but "equal or equivalent". To further ensure you are provided with quality locally produced Sapphire partition systems you may wish to specify a quality Sapphire coloured anodised finish from our extensive range. These finishes can seldom be achieved on inferior imported extrusions thus preventing substitution of inferior products.

* customised profiles are subject to minimum order quantites

Profiles are subject to change or deletion without notice Please check on availability prior to specifying or ordering.

back to top >>