CLIENT LOGIN
Sapphire Aluminium

Maxline 92mm – 132mm x 44mm Centre, Front & Double Glaze

52 Years of Aluminium Excellence

The Sapphire 92mm Maxline Suite is primarily used for framing plasterboard walls and glass where high performance is required.

Sapphire Maxline 92mm is the largest frame of our suites and is generally used for long lease projects such as schools, hospitals and embassies where long-term performance and acoustics are required.

INTRODUCTION

The Sapphire 92mm Maxline Suite is primarily used for framing plasterboard walls and glass where high performance is required . The system will accommodate steel mesh or fibre cement board behind the plasterboard where security and strength is a requirement. This system is much heavier in wall thickness and designed for a longer service life.

COMMON USE

Commercial Office Partitions, Schools, Hospitals, Universities and Government Fitouts (eg Embassies).

FRAME OPTIONS

STANDARD detail - 132mm x 45mm

GLAZING OPTIONS

  • Centre glazed   6mm - 12.38mm as per AS1288-2006
  • Front glazed      6mm - 14.50mm as per AS1288-2006
  • Double glazed  6mm - 14.50mm as per AS1288-2006

DOOR OPTIONS
HINGED - Timber or Glass Doors 32mm - 45mm in thickness
SLIDING - Timber or Sapphire Shooshline Alum Doors 45mm in thickness

DOOR STOPS
35mm, 40mm & 45mm Options to edge of frame
12mm High accepts acoustic seals and smoke seals

COLOURS

  • Available in all Sapphire Anodised Finishes and a wide range of Powdercoat Colours - Dulux or Interpon

AUSTRALIAN STANDARDS

Sapphire Aluminium products have been designed, manufactured and/or finished and are tested in accordance
with and to comply with the following Australian standards: AS 1288-2006, AS 1231-2000, AS3715-2002, AS1428.1-2009

PLASTERBOARD OPTIONS

  • 92mm Steel Studs and two sheets of 13mm plasterboard,
  • 76mm Steel Studs and three sheets of 13mm plasterboard
  • 64mm Steel Studs and four sheets of 13mm plasterboard.
  • 64mm Steel Studs and two sheets of 13mm, two sheets of 10mm plasterboard with 2 sheets of 3mm Stainless or Steel Sheet.
  • 51mm Steel Studs and four sheets of 13mm plasterboard and two sheets of 6mm fibre cement board.

Shadowline details optional Drywall construction optional (Semi- Demountable)

Additional Information

Acoustic Performance

 

WALLS
The 92mm Maxline suite will accommodate walls constructed with the following:

  • 92mm Steel Studs and two sheets of 13mm plasterboard,
  • 76mm Steel Studs and three sheets of 13mm plasterboard,
  • 64mm Steel Studs and four sheets of 13mm plasterboard,
  • 51mm Steel Studs and four sheets of 13mm plasterboard and two sheets of 6mm fibre cement board.

 

GLASS

  • Centre glazed – 6mm – 12.38mm as per AS1288-2006
  • Front glazed – 6mm – 14.50mm as per AS1288-2006
  • Double glazed – 6mm – 14.50mm as per AS1288-2006

Please note: The acoustic performance estimate of Sapphire Partition Systems is expressed in terms of Rw and Rw+Ctr. The performance of the as built system may be affected by – sound flanking and or the effectiveness of workmanship and other elements outside of Sapphire’s control.

*Hush refers to Comfort Huch or Viam Hush which are products produced and sold by CSR Viridian Glass.

Specification
SPECIFICATION
The Sapphire 92mm Maxline Suite of sections have been developed with over 25 years of experience in supply of suites to the partition industry and is designed to meet the relevant glazing codes and construction codes for internal framing, however fabricators of aluminium frames should seek certification by a consultant  engineer as to the framing being acceptable for the local design impact safety and deflection characteristics required of the site. Detailed calculations should be provided with final drawings of the aluminium frames.
ALLOY
The Sapphire 92mm Maxline Suite is extruded from primary billet only (No remelt) 6060T5 alloy ensuring that it is of the highest quality suitable for anodising finishes and maintaining colour uniformity from batch to batch.
ALUMINIUM
Partition suite to be 92mm Maxline by Sapphire Aluminium Pty Ltd (not “equal or equivalent”-see note below*) provided with the specified finish detailed in the finishes schedule and installed in accordance with the project design detail and relevant building codes.
Standard Frame
The maximum panel height shall be 3500mm.
HARDWARE
Glazing wedges shall be Sapphire’s colour coded wedges for 92mm Maxline® Partition Suite to suit standard glazing options.
Hinges shall be as per Sapphire Technical Manual.
All other hardware as per Sapphire Technical Manual.
FINISHES
All anodised material shall be produced by Sapphire to AS1231
All powder coated material shall be produced by Sapphire to AS3715
Care & Maintenance
Care & Maintenance
Sapphire 92mm Maxline Partition Suite should only ever need to be washed down with warm water and a mild detergent by rubbing with a soft cloth
Ensure that the cloth is rinsed well with fresh water to remove any detergent residue.
For more information refer to our website www.sapal.com.au
WARNING!
Strong detergents and abrasive cleaners should never be used to clean the Sapphire 92mm Maxline Partition Suite as it may cause scratching or damage to the coated surface.

Easy Product Enquiry

  • This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
  • This field is for validation purposes and should be left unchanged.

Additional Information

Acoustic Performance

 

WALLS
The 92mm Maxline suite will accommodate walls constructed with the following:

  • 92mm Steel Studs and two sheets of 13mm plasterboard,
  • 76mm Steel Studs and three sheets of 13mm plasterboard,
  • 64mm Steel Studs and four sheets of 13mm plasterboard,
  • 51mm Steel Studs and four sheets of 13mm plasterboard and two sheets of 6mm fibre cement board.

 

GLASS

  • Centre glazed – 6mm – 12.38mm as per AS1288-2006
  • Front glazed – 6mm – 14.50mm as per AS1288-2006
  • Double glazed – 6mm – 14.50mm as per AS1288-2006

Please note: The acoustic performance estimate of Sapphire Partition Systems is expressed in terms of Rw and Rw+Ctr. The performance of the as built system may be affected by – sound flanking and or the effectiveness of workmanship and other elements outside of Sapphire’s control.

*Hush refers to Comfort Huch or Viam Hush which are products produced and sold by CSR Viridian Glass.

Specification
SPECIFICATION
The Sapphire 92mm Maxline Suite of sections have been developed with over 25 years of experience in supply of suites to the partition industry and is designed to meet the relevant glazing codes and construction codes for internal framing, however fabricators of aluminium frames should seek certification by a consultant  engineer as to the framing being acceptable for the local design impact safety and deflection characteristics required of the site. Detailed calculations should be provided with final drawings of the aluminium frames.
ALLOY
The Sapphire 92mm Maxline Suite is extruded from primary billet only (No remelt) 6060T5 alloy ensuring that it is of the highest quality suitable for anodising finishes and maintaining colour uniformity from batch to batch.
ALUMINIUM
Partition suite to be 92mm Maxline by Sapphire Aluminium Pty Ltd (not “equal or equivalent”-see note below*) provided with the specified finish detailed in the finishes schedule and installed in accordance with the project design detail and relevant building codes.
Standard Frame
The maximum panel height shall be 3500mm.
HARDWARE
Glazing wedges shall be Sapphire’s colour coded wedges for 92mm Maxline® Partition Suite to suit standard glazing options.
Hinges shall be as per Sapphire Technical Manual.
All other hardware as per Sapphire Technical Manual.
FINISHES
All anodised material shall be produced by Sapphire to AS1231
All powder coated material shall be produced by Sapphire to AS3715
Care & Maintenance
Care & Maintenance
Sapphire 92mm Maxline Partition Suite should only ever need to be washed down with warm water and a mild detergent by rubbing with a soft cloth
Ensure that the cloth is rinsed well with fresh water to remove any detergent residue.
For more information refer to our website www.sapal.com.au
WARNING!
Strong detergents and abrasive cleaners should never be used to clean the Sapphire 92mm Maxline Partition Suite as it may cause scratching or damage to the coated surface.